Go to the first, previous, next, last section, table of contents.

Managing Curves

The g f command is really shorthand for the following commands: C-u g d g a g p. Likewise, g F is shorthand for C-u g d g A g p. You can gain more control over your graph by using these commands directly.

The g a (calc-graph-add) command adds the "curve" represented by the two values on the top of the stack to the current graph. You can have any number of curves in the same graph. When you give the g p command, all the curves will be drawn superimposed on the same axes.

The g a command (and many others that affect the current graph) will cause a special buffer, `*Gnuplot Commands*', to be displayed in another window. This buffer is a template of the commands that will be sent to GNUPLOT when it is time to draw the graph. The first g a command adds a plot command to this buffer. Succeeding g a commands add extra curves onto that plot command. Other graph-related commands put other GNUPLOT commands into this buffer. In normal usage you never need to work with this buffer directly, but you can if you wish. The only constraint is that there must be only one plot command, and it must be the last command in the buffer. If you want to save and later restore a complete graph configuration, you can use regular Emacs commands to save and restore the contents of the `*Gnuplot Commands*' buffer.

If the values on the stack are not variable names, g a will invent variable names for them (of the form `PlotDatan') and store the values in those variables. The "x" and "y" variables are what go into the plot command in the template. If you add a curve that uses a certain variable and then later change that variable, you can replot the graph without having to delete and re-add the curve. That's because the variable name, not the vector, interval or formula itself, is what was added by g a.

A numeric prefix argument on g a or g f changes the way stack entries are interpreted as curves. With a positive prefix argument n, the top n stack entries are "y" values for n different curves which share a common "x" value in the n+1st stack entry. (Thus g a with no prefix argument is equivalent to C-u 1 g a.)

A prefix of zero or plain C-u means to take two stack entries, "x" and "y" as usual, but to interpret "y" as a vector of "y" values for several curves that share a common "x".

A negative prefix argument tells Calc to read n vectors from the stack; each vector [x, y] describes an independent curve. This is the only form of g a that creates several curves at once that don't have common "x" values. (Of course, the range of "x" values covered by all the curves ought to be roughly the same if they are to look nice on the same graph.)

For example, to plot @c{$\sin n x$} sin(n x) for integers n from 1 to 5, you could use v x to create a vector of integers (n), then V M ' or V M $ to map `sin(n x)' across this vector. The resulting vector of formulas is suitable for use as the "y" argument to a C-u g a or C-u g f command.

The g A (calc-graph-add-3d) command adds a 3D curve to the graph. It is not legal to intermix 2D and 3D curves in a single graph. This command takes three arguments, "x", "y", and "z", from the stack. With a positive prefix n, it takes n+2 arguments (common "x" and "y", plus n separate "z"s). With a zero prefix, it takes three stack entries but the "z" entry is a vector of curve values. With a negative prefix -n, it takes n vectors of the form [x, y, z]. The g A command works by adding a splot (surface-plot) command to the `*Gnuplot Commands*' buffer.

(Although g a adds a 2D plot command to the `*Gnuplot Commands*' buffer, Calc changes this to splot before sending it to GNUPLOT if it notices that the data points are evaluating to xyz calls. It will not work to mix 2D and 3D g a curves in a single graph, although Calc does not currently check for this.)

The g d (calc-graph-delete) command deletes the most recently added curve from the graph. It has no effect if there are no curves in the graph. With a numeric prefix argument of any kind, it deletes all of the curves from the graph.

The g H (calc-graph-hide) command "hides" or "unhides" the most recently added curve. A hidden curve will not appear in the actual plot, but information about it such as its name and line and point styles will be retained.

The g j (calc-graph-juggle) command moves the curve at the end of the list (the "most recently added curve") to the front of the list. The next-most-recent curve is thus exposed for g d or similar commands to use. With g j you can work with any curve in the graph even though curve-related commands only affect the last curve in the list.

The g p (calc-graph-plot) command uses GNUPLOT to draw the graph described in the `*Gnuplot Commands*' buffer. Any GNUPLOT parameters which are not defined by commands in this buffer are reset to their default values. The variables named in the plot command are written to a temporary data file and the variable names are then replaced by the file name in the template. The resulting plotting commands are fed to the GNUPLOT program. See the documentation for the GNUPLOT program for more specific information. All temporary files are removed when Emacs or GNUPLOT exits.

If you give a formula for "y", Calc will remember all the values that it calculates for the formula so that later plots can reuse these values. Calc throws out these saved values when you change any circumstances that may affect the data, such as switching from Degrees to Radians mode, or changing the value of a parameter in the formula. You can force Calc to recompute the data from scratch by giving a negative numeric prefix argument to g p.

Calc uses a fairly rough step size when graphing formulas over intervals. This is to ensure quick response. You can "refine" a plot by giving a positive numeric prefix argument to g p. Calc goes through the data points it has computed and saved from previous plots of the function, and computes and inserts a new data point midway between each of the existing points. You can refine a plot any number of times, but beware that the amount of calculation involved doubles each time.

Calc does not remember computed values for 3D graphs. This means the numerix prefix argument, if any, to g p is effectively ignored if the current graph is three-dimensional.

The g P (calc-graph-print) command is like g p, except that it sends the output to a printer instead of to the screen. More precisely, g p looks for `set terminal' or `set output' commands in the `*Gnuplot Commands*' buffer; lacking these it uses the default settings. However, g P ignores `set terminal' and `set output' commands and uses a different set of default values. All of these values are controlled by the g D and g O commands discussed below. Provided everything is set up properly, g p will plot to the screen unless you have specified otherwise and g P will always plot to the printer.


Go to the first, previous, next, last section, table of contents.